Switch Control - Revision history

Support: /* Reset secret pass */

2013-01-11T22:12:06Z

Reset secret pass

← Older revision		Revision as of 15:12, 11 January 2013
Line 2,208:		Line 2,208:
	service password-encryption		service password-encryption
	enable secret PASS</pre>		enable secret PASS</pre>

	~~# f=1; while [ $f -le 24 ]; do echo "int fa0/$f"; echo "switchport access vlan 300"; f=`expr $f + 1`; done~~
	~~int fa0/1~~

Support: /* Reset secret pass */

2013-01-11T22:10:03Z

Reset secret pass

← Older revision		Revision as of 15:10, 11 January 2013
Line 2,204:		Line 2,204:

	= Reset secret pass =		= Reset secret pass =
	~~Last updated: 2010-08-05~~

	conf t		<pre>conf t
	service password-encryption		service password-encryption
	enable secret PASS		enable secret PASS</pre>

	# f=1; while [ $f -le 24 ]; do echo "int fa0/$f"; echo "switchport access vlan 300"; f=`expr $f + 1`; done		# f=1; while [ $f -le 24 ]; do echo "int fa0/$f"; echo "switchport access vlan 300"; f=`expr $f + 1`; done
	int fa0/1		int fa0/1

Support: /* Writing commands for IOS missing "int range" */

2013-01-11T22:09:37Z

Writing commands for IOS missing "int range"

← Older revision		Revision as of 15:09, 11 January 2013
Line 2,146:		Line 2,146:

	= Writing commands for IOS missing "int range" =		= Writing commands for IOS missing "int range" =
	~~Last updated: 2010-06-04~~

	# f=1; while [ $f -le 24 ]; do echo "int fa0/$f"; echo "switchport access vlan 300"; f=`expr $f + 1`; done		(get to sh shell)

			<pre># f=1; while [ $f -le 24 ]; do echo "int fa0/$f"; echo "switchport access vlan 300"; f=`expr $f + 1`; done
	int fa0/1		int fa0/1
	switchport access vlan 300		switchport access vlan 300
Line 2,200:		Line 2,201:
	switchport access vlan 300		switchport access vlan 300
	int gi0/2		int gi0/2
	switchport access vlan 300		switchport access vlan 300</pre>

	= Reset secret pass =		= Reset secret pass =

Support: /* Configure 2924 (castle) */

2013-01-11T22:08:48Z

Configure 2924 (castle)

← Older revision		Revision as of 15:08, 11 January 2013
Line 2,126:		Line 2,126:
	wr mem		wr mem

	Configure a 2924 trunk		= Configure a 2924 trunk =
	~~Last updated 2010-08-05~~

	conf t		<pre>conf t
	interface FastEthernet0/1		interface FastEthernet0/1
	description Uplink to p1a		description Uplink to p1a
Line 2,144:		Line 2,143:
	switchport trunk allowed vlan 1,50,300,1002-1005		switchport trunk allowed vlan 1,50,300,1002-1005
	switchport mode trunk		switchport mode trunk
	no spanning-tree portfast		no spanning-tree portfast</pre>

	= Writing commands for IOS missing "int range" =		= Writing commands for IOS missing "int range" =

Support: /* Configure 2924 (castle) */

2013-01-11T22:07:57Z

Configure 2924 (castle)

← Older revision		Revision as of 15:07, 11 January 2013
Line 1,929:		Line 1,929:

	= Configure 2924 (castle) =		= Configure 2924 (castle) =
	~~Last updated 2011-01-26~~

	# reset		* reset
	write erase		<pre>write erase
	reload		reload</pre>
	~~# enter basic setup "setup"~~

	# setup vlans		* enter basic setup "setup"
	conf t		* setup vlans
			<pre>conf t
	interface VLAN1		interface VLAN1
	no ip address		no ip address
Line 1,949:		Line 1,948:
	int vlan300		int vlan300
	no shutdown		no shutdown
	end		end</pre>

	# setup trunk port		* setup trunk port
	conf t		<pre>conf t
	interface FastEthernet0/1		interface FastEthernet0/1
	description Uplink to p1a		description Uplink to p1a
Line 1,970:		Line 1,969:
	switchport mode trunk		switchport mode trunk
	no spanning-tree portfast		no spanning-tree portfast
	end		end</pre>

	# setup ports		* setup ports
	conf t		<pre>conf t
	interface FastEthernet0/3		interface FastEthernet0/3
	switchport access vlan 50		switchport access vlan 50
Line 2,083:		Line 2,082:
	spanning-tree portfast		spanning-tree portfast
	no desc		no desc
	end		end</pre>

	# config terminal. setup timeout, priv level		* config terminal. setup timeout, priv level
	conf t		<pre>conf t
	line con 0		line con 0
	exec-timeout 10		exec-timeout 10
Line 2,092:		Line 2,091:
	exec-timeout 10		exec-timeout 10
	privilege level 0		privilege level 0
	end		end</pre>

	# setup web user		* setup web user
	conf t		<pre>conf t
	service password-encryption		service password-encryption
	username web privilege 15 password xxxxxxxx		username web privilege 15 password xxxxxxxx
	end		end</pre>

	# enable http passwd checking, disable http,		* enable http passwd checking, disable http,
	conf t		<pre>conf t
	ip http authentication local		ip http authentication local
	#no ip http server (only http avail on 2950)		#no ip http server (only http avail on 2950)
	end		end</pre>

	# lock down ssh/web/telnet access		* lock down ssh/web/telnet access
	conf t		<pre>conf t
	access-list 1 permit 10.1.4.5		access-list 1 permit 10.1.4.5
	end		end</pre>


	# time		* time
	conf t		<pre>conf t
	clock summer-time PDT recurring 2 Sunday March 2:00 1 Sunday November 2:00		clock summer-time PDT recurring 2 Sunday March 2:00 1 Sunday November 2:00
	clock timezone PST -8		clock timezone PST -8
Line 2,124:		Line 2,122:
	no snmp-server community public RO		no snmp-server community public RO
	snmp-server community jc292401 RO 1		snmp-server community jc292401 RO 1
	end		end</pre>

	wr mem		wr mem

	Configure a 2924 trunk		Configure a 2924 trunk

Support: /* Configure 2924 (i2b) */

2013-01-11T22:05:43Z

Configure 2924 (i2b)

← Older revision		Revision as of 15:05, 11 January 2013
Line 1,924:		Line 1,924:
	no snmp-server community public RO		no snmp-server community public RO
	snmp-server community jc292401 RO 20		snmp-server community jc292401 RO 20
	end		end</pre>

	wr mem~~</pre>~~		wr mem

	= Configure 2924 (castle) =		= Configure 2924 (castle) =

Support: /* Configure 2950 */

2013-01-11T22:05:21Z

Configure 2950

← Older revision		Revision as of 15:05, 11 January 2013
Line 1,736:		Line 1,736:
	no snmp-server community public RO		no snmp-server community public RO
	snmp-server community jc292401 RO 20		snmp-server community jc292401 RO 20
	end		end</pre>

	wr mem~~</pre>~~		wr mem

	= Configure 2924 (i2b) =		= Configure 2924 (i2b) =

Support: /* Configure 2960 */

2013-01-11T22:05:02Z

Configure 2960

← Older revision		Revision as of 15:05, 11 January 2013
Line 1,570:		Line 1,570:
	no snmp-server community public RO		no snmp-server community public RO
	snmp-server community jc292401 RO 20		snmp-server community jc292401 RO 20
	end		end</pre>
	~~wr mem~~</pre>
			wr mem

	= Configure 2950 =		= Configure 2950 =

70.230.212.110: /* Configure 2924 (i2b) */

2013-01-11T01:26:42Z

Configure 2924 (i2b)

← Older revision		Revision as of 18:26, 10 January 2013
Line 1,742:		Line 1,742:
	Last updated 2010-11-05		Last updated 2010-11-05

	# reset		* reset
	write erase		<pre>write erase
	reload		reload</pre>
	~~# enter basic setup~~

	# setup vlans		* enter basic setup
	conf t		* setup vlans
			<pre>conf t
	interface VLAN1		interface VLAN1
	no ip address		no ip address
Line 1,760:		Line 1,760:
	int vlan300		int vlan300
	no shutdown		no shutdown
	end		end</pre>

	# setup mgmt ports		* setup mgmt ports
	conf t		<pre>conf t
	int fa0/24		int fa0/24
	switchport access vlan 300		switchport access vlan 300
	description ats-8 - priv		description ats-8 - priv
	spanning-tree portfast		spanning-tree portfast
	end		end</pre>

	# setup trunk port		* setup trunk port
	conf t		<pre>conf t
	interface FastEthernet0/1		interface FastEthernet0/1
	description Uplink to p20		description Uplink to p20
Line 1,779:		Line 1,779:
	switchport mode trunk		switchport mode trunk
	no spanning-tree portfast		no spanning-tree portfast
	end		end</pre>

	# setup ports		* setup ports
	conf t		<pre>conf t
	interface FastEthernet0/2		interface FastEthernet0/2
	spanning-tree portfast		spanning-tree portfast
Line 1,870:		Line 1,870:
	spanning-tree portfast		spanning-tree portfast
	no desc		no desc
	end		end</pre>

	# config terminal. setup timeout, priv level		* config terminal. setup timeout, priv level
	conf t		<pre>conf t
	line con 0		line con 0
	exec-timeout 10		exec-timeout 10
Line 1,879:		Line 1,879:
	exec-timeout 10		exec-timeout 10
	privilege level 0		privilege level 0
	end		end</pre>

	# setup web user		* setup web user
	conf t		<pre>conf t
	service password-encryption		service password-encryption
	username web privilege 15 password xxxxxxxx		username web privilege 15 password xxxxxxxx
	end		end</pre>

	# enable http passwd checking, disable http,		* enable http passwd checking, disable http,
	conf t		<pre>conf t
	ip http authentication local		ip http authentication local
	#no ip http server (only http avail on 2950)		#no ip http server (only http avail on 2950)
	end		end</pre>

	# lock down ssh/web/telnet access		* lock down ssh/web/telnet access
	conf t		<pre>conf t
	access-list 100 permit ip host 69.55.233.196 any		access-list 100 permit ip host 69.55.233.196 any
	access-list 100 permit ip host 99.150.247.226 any		access-list 100 permit ip host 99.150.247.226 any
Line 1,905:		Line 1,905:
	ip access-group 100 out		ip access-group 100 out

	end		end</pre>


	# time		* time
	conf t		<pre>conf t
	clock summer-time PDT recurring 2 Sunday March 2:00 1 Sunday November 2:00		clock summer-time PDT recurring 2 Sunday March 2:00 1 Sunday November 2:00
	clock timezone PST -8		clock timezone PST -8
Line 1,925:		Line 1,925:
	end		end

	wr mem		wr mem</pre>

	= Configure 2924 (castle) =		= Configure 2924 (castle) =

70.230.212.110: /* Configure 2950 */

2013-01-11T01:24:12Z

Configure 2950

← Older revision		Revision as of 18:24, 10 January 2013
Line 1,589:		Line 1,589:
	end</pre>		end</pre>

	## ONLY for p20 ##		* ## ONLY for p20 ##
	<pre>int GigabitEthernet0/1		<pre>int GigabitEthernet0/1
	description Connection from i2b		description Connection from i2b
Line 1,625:		Line 1,625:
	end</pre>		end</pre>

	## END p20 ##		* ## END p20 ##


	## normal switches ##		* ## normal switches ##

	* setup ports		* setup ports
Line 1,652:		Line 1,652:
	end</pre>		end</pre>

	## END normal switches ##		* ## END normal switches ##

	* config terminal. setup timeout, priv level		* config terminal. setup timeout, priv level